{"code":1,"message":"success","data":{"id":235,"titleCn":"【彩云评测】神马M30S-88TSHA256服务器","titleEn":"[Evaluation Report ] MicroBT WhatsMiner M30S-88T SHA256 Server","contentCn":"

2019年12月7日，比特微发布了一段神马M30SSHA256服务器的运行视频，宣布新一代神马M30成功问世，无论是整机算力还是算力的单位功耗均刷新行业纪录！

很快彩云小分队收到了神马M30S-88T的工程样机，以下彩云小分队就为大家带来神马M30S-88T产品的第三方独立体验评测。

 

【神马M30S-88T官方参数】

 

 

【神马M30S-88T外观】

神马M30S-88T外包装比较简洁（因为是工程样机暂时采用M20S的外包装），整机外包装尺寸485x230x355mm，物流重量11.4kg，比神马M20S-68T（12.3kg)轻了少许▼

 

 

下面是官方提供的M30S未来将使用的外包装图片，可以看到和M20S一致，在外包装纸箱上除了物流标识外还贴有机器型号、算力、SN码等信息的标签。

内部使用类似神马M20S-68T的珍珠泡棉包装▼

 

 

神马M30S-88T整体外观和M20S-68T一致，依然为单筒设计，外观尺寸390x150x225mm，重量10.5kg ▼

 

 

神马M30S-88T和M20S-68T的区别在于电源更换成扁平样式，使得整机高度降低了15mm,同时整机的重量比M20S-68T更轻了0.9kg ▼

 

 

侧面是神马M30S-88T的产品标识，另一侧是产品使用注意事项等信息 ▼

 

 

整机使用了一进一出两风扇散热，进风口风扇装有金属防护罩（矿场运维小技巧：类似设计的产品由于长途运输，产品到货后会可能发生风扇报异常，原因是金属防护罩压住了风扇扇叶导致，只要将金属防护罩往外拉出一点即可 ）▼

 

 

【神马M30S-88T内部细节】

接下来我们来探究一下刷新行业功耗比新纪录神马M30S-88T的内部，拆除控制板周边的4个固定螺丝，取下控制板上的电源调压线和连接算力板的数据线即可拆下控制板 ▼

 

 

神马M30S-88T使用的是H3的控制板，通过转接板的连接线与算力板连接，面板接口、按钮都没有变化 ▼

 

 

在控制板外壳上还标识有型号、算力、SN码以及网卡MAC地址等信息 ▼

 

 

神马M30S-88T标配了一个型号为P21-GB-12-3300的电源 ▼

 

 

神马M30S-88T电源在外形上做了一些改变，比较之前型号高度降低，长度加长到与出风口风扇对齐的位置 ▼

 

 

神马M30S-88T使用16A电源线供电，插口位置也调整到中间 ▼

 

 

神马M30S-88T的散热使用了两个14038 12V 7.2A的风扇▼

 

 

神马M30S-88T的风扇功率（7.2A）比M20系列（9A）更低，降低的不只是小小的功耗，也预示着噪音会更小 ▼

 

 

前风扇采用了6芯扁平接口，后风扇使用的是4芯4P接口，可以看出产品前后两个风扇互相不通用 ▼

 

 

神马M30S-88T机箱采用铝合金压铸一体成型，算力板通过凹槽插入固定，排列紧密 ▼

 

 

神马M30S-88T内置了3块算力板，每块算力板上有148颗三星8nm ASIC芯片，共444颗芯片  

 

 

算力板两面都有散热片覆盖，中间涂有导热硅脂，使用26颗弹簧螺丝加固 ▼

 

 

下图是官方提供的将算力版散热片取下后的算力板裸视图

 

神马M30S-88T整机分解图示 ▼

 

【神马M30S-88T安装配置】

开箱检查线材没有脱落和异响后将机器插上电源线和网线，进入本地网络的路由器内查找名为“MicroBT”的IP地址或使用网卡MAC地址或者下载 神马管理工具查找到对应的的IP地址 ▼

 

 

打开浏览器，在地址栏内输入找到的机器的IP地址（多台机器可直接在神马管理工具内操作），进入登录页面，默认用户名密码都是：admin，进入控制台首页 ▼

 

 

点击上侧菜单栏“Configuration/CGMiner Configuration\"进入矿池设置界面修改矿池信息 ▼

 

 

修改“Pool 1”主矿池地址

修改“Pool 1 worker\"矿工名（查看矿池帮助）

修改“Pool 1 password\"矿工密码（任意字母数字）


根据需要修改备用矿池“Pool 2\"和“Pool 3\"，设置完成后点击“Save&Apply\"按钮保存并应用设置好的配置 ▼

 

 

 

有一点要注意的是修改矿池时需要先点击矿池地址栏，在下拉菜单中选择“Custom”后方可修改地址 ▼

 

 

点击“status/Overview”可以查看系统和固件版本等信息 ▼

 

 

点击“Configuration/Interfaces”可将默认的IP地址获取方式由自动获取修改为静态IP地址  ▼

 

 

点击“status/CGminer Status”可回到首页查看当前运行情况，选择“system/reboot”可对其进行重启操作 ▼

 

 

【神马M30S-88T测试数据】


测试环境噪音值44分贝▼

 

 

神马M30S-88T开机后的半小时内会自动调频，此阶段算力在24T波动，半小时后程序会自动重启，算力值才会达标，运行正常，算力稳定达标后测得温度情况：算力板温度71-72度，进风口25.6度；出风口60.4度；侧面温度36.1度 ▼

 

 

电源温度情况：出风口55度；连接铜片31.3度；电源线26度 ▼

 

 

整机正常运行时噪音水平为85.7分贝，运行功耗为3345W，与官方公布的3344W一致 ▼

 

 

经过彩云对神马M30S-88T进行了24小时的测试后，得出算力情况如下 ：控制台显示的平均算力约88.41T ▼

 

从以上得出24小时接收到的算力为89.11T，算力平稳，计算得出神马M30S-88T功耗比为37.53W/T  ▼

 

 

【神马M30S-88T评测总结】

 神马M30S-88T运行时的状态延续了之前神马的特性“稳”，产品长时间测试中运行稳定，算力、功率、温度等波动幅度很小；

 改良的电源缩小了体积也减轻了重量，对运维带来了一定的便利；

 产品前后风扇的接口不一致会对后期风扇备件带来些困扰，希望后期量产时会有改进；

 官方称M30系列也会有其它型号，具体参数会在稍后公布。


到这里此次彩云评测就结束了，神马M30SSHA256服务器单机88T算力，功耗比37.55W/T的测试成绩着实震撼到了小编。


对于神马M30全系列SHA256服务器官方称功耗比都将低于50W/T，通过M30S的测试可以预见一贯秉承“成功可见”原则的神马已经真正开启功耗比4X新时代！

","contentEn":"

On December 7th, 2019, MicroBT released a running video of WhatsMiner M30S SHA256 server, announcing the successful launch of the new generation of the WhatsMiner M30 server, both the hashrate and the power ratio broke the new industry records!

Soon cybtc.com received the sample of WhatsMiner M30S-88T. Here is the third-party experience evaluation of WhatsMiner M30S-88T server from Caiyun team.

Official Specifications of WhatsMiner M30S-88T

 

Appreance of WhatsMiner M30S-88T

he package of WhatsMiner M30S-88T is simple because it is the sample and it is the same as the M20S package), the package size of the whole machine is 485x230x355mm, the logistics weight is 11.4kg, which is a little lighter than WhatsMiner M20S-68T (12.3kg) ▼

 

 

Here is the official picture of the M30S packaging to be used in the near future, which is consistent with M20S. In addition to the logistics identification, the outer packaging carton is labeled with information such as the model number, hashrate and SN number.

 

 

Using pearl foam packaging inside which is similar to WhatsMiner M20S-68T ▼

 

 

 

The overall appearance of WhatsMiner M30S-88T is the same as the M20S-68T, and it is still a single cylinder design. The appearance size is 390x150x225mm and the weight is 10.5kg ▼

 

 

The difference between M30S-88T and M20S-68T is that the power supply is replaced with a flat style, which reduces the height of the whole machine by 15mm, and the weight of the whole machine is 0.9kg lighter than the M20S-68T.▼

 

 

On the side is the logo of M30S-88T, and on the other side is information such as precautions▼

 

 

The whole machine uses one input, one output and two fans for cooling, and the air inlet fan is equipped with a metal protective cover. It is caused by the metal protective cover pressing the fan blades, as long as the metal protective cover is pulled out a little) ▼

 

 

WhatsMiner M30S-88T Details

Next, let's see M30S power consumption. Inside the WhatsMiner M30S-88T, remove the four fixing screws around the control board, remove the power supply regulator line on the control board and the data line connected to the hash board, and then remove the control board▼

 

 

The WhatsMiner M30S-88T server uses the H3 control board. It is connected to the hash board through the cable of the adapter board. The panel interface and buttons are the same as before.▼

 

 

The control board is also marked with the model, hashrate, SN code, and network card MAC address. ▼

 

 

The WhatsMiner M30S-88T comes standard with a power supply model P21-GB-12-3300 ▼

 

 

The WhatsMiner M30S-88T power supply has made some changes in the shape. Compared with the previous model, the height has been reduced and the length has been extended to the position aligned with the air outlet fan. ▼

 

 

WhatsMiner M30S-88T uses 16A power cord for the power supply, and the socket position is also adjusted to the middle ▼

 

 

The cooling of the WhatsMiner M30S-88T uses two 14038 12V 7.2A fans▼

 

 

The fan power (7.2A) of the WhatsMiner M30S-88T is lower than that of the M20 series (9A), which reduces not only the power consumption, but also the noise.▼

 

 

The front fan uses a 6-core flat interface, and the rear fan uses a 4-core 4P interface. ▼

 

 

The WhatsMiner M30S-88T chassis is made of aluminum alloy die-casting, and the hash board is inserted and fixed through the groove, which is closely arranged.▼

 

 

The WhatsMiner M30S-88T has 3 built-in hash boards, each of which has 148 Samsung 8nm ASIC chips, a total of 444

 

 

The hash board is covered by heat sinks on both sides, coated with thermal grease in the middle, and reinforced with 26 spring screws ▼

 

 

The following figure is a bare view of the hash board after the hash board is officially removed.

 

 

WhatsMiner M30S-88T machine decomposition diagram ▼

 

 

WhatsMiner M30S-88T Installation Configuration

Open the box and check that the miner wires have not fallen off or abnormal noises. Plug the machine into a power cable and a network cable. Enter the local network router to find the IP address named \"MicroBT\" or use the MAC address of the network card or download the Shenma miner management tool. Find the IP address of the miner▼

 

 

Open the browser and enter the IP address of the miner found in the address bar (multiple miners can be directly operated in the WhatsMiner Tool) to enter the login page. The default username and password are: admin Console home▼

 

 

Click \"Configuration / CGMiner Configuration\" in the upper menu bar to enter the pool setting interface to modify the pool information ▼

 

 

Modify \"Pool 1\" main mining pool address

Modify \"Pool 1 worker\" miner name (see the pool help)

Modify \"Pool 1 password\" miner password (any alphanumeric)

Modify the backup pools \"Pool 2\" and \"Pool 3\" as required. After setting, click the \"Save & Apply\" button to save and apply the set configuration.▼

 

 

One thing to note is that when modifying the mining pool, you need to click the pool address bar first, and then select \"Custom\" in the drop-down menu to modify the address. ▼

 

 

Click \"status / Overview\" to view system and firmware version information ▼

 

 

Click \"Configuration / Interfaces\" to change the default IP address acquisition method from automatic acquisition to static IP address ▼

 

 

Click \"status / CGminer Status\" to return to the homepage to check the current running status of the miner, select \"system / reboot\" to restart the machine ▼

 

 

WhatsMiner M30S-88T Test Data


Test ambient noise value is 44 dB▼

 

The WhatsMiner M30S-88T will automatically tune frequency within half an hour after it is turned on. At this stage, the hashrate fluctuates at 24T. After half an hour, the program will automatically restart. The hashrate value will reach the standard. The machine runs normally. Temperature conditions: The hash board temperature is 71-72 degrees, the air inlet is 25.6 degrees, the air outlet is 60.4 degrees, and the side temperature of the machine is 36.1 degrees▼

 

 

Power supply temperature: 55 degree for the air outlet; 31.3 degree for the copper connection; 26 degree for the power cord ▼

 

 

When the machine is running normally, the noise level is 85.7 dB, and the operating power consumption is 3345W, which is consistent with the official 3344W.▼

 

 

After Caiyun team conducted a 24-hour test on the WhatsMiner M30S-88T, the hashrate is as follows: The average hashrate displayed on the console is about 88.41T ▼

 

 

The hashrate received by the mining pool for 24 hours is 89.11T, and the hashrate is stable. The power ratio of the WhatsMiner M30S-88T is calculated to be 37.53W / T ▼

 

 

WhatsMiner M30S-88T Evaluation Summary

 

 The running state of WhatsMiner M30S-88T continues the previous characteristics of \"stable\". The miner runs stably during long-term testing, and the fluctuations of computing power, power, and temperature are small;

 Improved power supply reduces volume and weight, bringing certain convenience to the operation and maintenance of the mine；

 The inconsistent fan interface on the front and rear of the miner will cause some troubles to the fan spare parts in the later period, and hope that there will be improvements in the later mass production；

 The official said that the M30 series will also have other models, the specific parameters will be announced later


At this point, the evaluation of Caiyun team is over. WhatsMiner M30S SHA256 server is with 88T hashrate and 37.55W/T power ratio. The test results have really shocked the editor.


For the full range of WhatsMiner M30 series SHA256 server whose power consumption ratio will be lower than 50W/T. Through the test of M30S, it can be foreseen that the WhatsMiner, which has always adhered to the \"visible success\" principle, has really leaded the industry to the new era!

","introductionCn":"","introductionEn":"Here is the third-party experience evaluation of WhatsMiner M30S-88T server from Caiyun team.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E5%BD%A9%E4%BA%91%E8%AF%84%E6%B5%8B_1768462998068.jpg","channelId":2,"publishName":"cybtc.com","publishDate":"2019-12-25","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 16:05:26","updateTime":"2026-01-15 15:43:19","tagIdList":[59,56],"otherNewsList":[{"id":293,"titleCn":"","titleEn":"WhatsMiner Immersion-cooling M66S++ Test Report","introductionCn":"","introductionEn":"The test report of WhatsMiner immersion-cooling M66S++ from Hash House Tech.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/1745721421659%E6%9C%AA%E5%91%BD%E5%90%8D%285%29.jpg","channelId":2,"publishName":"MicroBT","publishDate":"2025-04-27","status":1,"isTop":1,"isRecommend":0,"isDeleted":0,"createTime":"2025-04-27 10:38:19","updateTime":"2025-05-14 15:44:39"},{"id":276,"titleCn":"","titleEn":"WhatsMiner Immersion-cooling M66S Test Report","introductionCn":"","introductionEn":"The test report of WhatsMiner immersion-cooling M66S from Hash House Tech.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/1700817283299M66S%20unboxing.png","channelId":2,"publishName":"by Hash House Tech","publishDate":"2023-11-24","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2023-11-24 17:17:44","updateTime":"2025-05-14 15:47:13"},{"id":225,"titleCn":"神马M30系列首批限量现货回馈活动已结束","titleEn":"The First Batch of WhatsMiner M30 Series in Stock Has Been Sold Out","introductionCn":"","introductionEn":"The batch of WhatsMiner M30 series in stock released on March 30, at 7 pm (PST) has been sold out.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E5%9B%9E%E9%A6%88%E7%BB%93%E6%9D%9F_1768461434603.jpg","channelId":1,"publishName":"WhatsMiner Marketing","publishDate":"2021-04-08","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:15:00","updateTime":"2026-01-15 15:17:18"},{"id":224,"titleCn":"神马M30系列限量现货将于3月31日上线官网","titleEn":"A Batch of WhatsMiner M30 Series in Stock Will Go on Sale on March 30","introductionCn":"","introductionEn":"MicroBT will release a batch of WhatsMiner M30 series in stock on March 30, at 7 pm (PST) on official online shop www.whatsminer.com to give back to all customers. ","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/M30%E4%B8%8A%E7%BA%BF%E9%99%90%E9%87%8F%E9%94%80%E5%94%AE_1768461522432.jpg","channelId":1,"publishName":"WhatsMiner Marketing ","publishDate":"2021-03-25","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:13:31","updateTime":"2026-01-15 15:18:45"},{"id":219,"titleCn":"比特微与Foundry紧密合作，加速北美矿业繁荣","titleEn":"MicroBT Partners With Foundry, Strengthens Foothold in North America","introductionCn":"","introductionEn":"MicroBT announced its cooperation with Foundry and the establishment of overseas production to provide a stable supply chain for North American investors and jointly accelerate the mining industry.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E5%8A%A0%E9%80%9F%E5%8C%97%E7%BE%8E%E7%B9%81%E8%8D%A3_1768461662753.jpg","channelId":1,"publishName":"WhatsMiner Marketing ","publishDate":"2020-09-25","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:07:06","updateTime":"2026-01-15 15:21:06"},{"id":217,"titleCn":"比特微已向Hut8交付首批2000台神马M30系列产品","titleEn":"The First Batch of 2000 WhatsMiner M30 Machines Purchased by Hut8 Was Delivered","introductionCn":"","introductionEn":"MicroBT has delivered the first batch of 2000 pieces of WhatsMiner M31S and M31S+ purchased by Hut8.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E4%BA%A4%E4%BB%982000_1768461711433.jpg","channelId":1,"publishName":"WhatsMiner Marketing","publishDate":"2020-08-17","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:04:22","updateTime":"2026-01-15 15:21:53"},{"id":216,"titleCn":"Blockstream携手神马进入3X新时代","titleEn":"Blockstream Stepped into 3X Era Together with WhatsMiner","introductionCn":"","introductionEn":"Blockstream's purchase of WhatsMiner M30 series better illustrates that WhatsMiner is the better choice for investors in the mining industry. ","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/3X%E6%97%B6%E4%BB%A3_1768461750965.jpg","channelId":1,"publishName":"WhatsMiner Marketing Team","publishDate":"2020-07-10","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:03:21","updateTime":"2026-01-15 15:22:33"},{"id":229,"titleCn":"比特微带领行业全面迈入3X时代","titleEn":"Step into 3X era with WhatsMiner","introductionCn":"","introductionEn":"WhatsMiner expanded the M30S series to three products with 3X J/T which leads the industry into the 3X era.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E8%BF%88%E5%85%A53X_1768461826279.jpg","channelId":1,"publishName":"WhatsMiner","publishDate":"2020-04-24","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 15:35:55","updateTime":"2026-01-15 15:23:48"},{"id":214,"titleCn":"【3X共赢 极致可见】神马邀您共赏M30新品全球线上发","titleEn":"Welcome to Join the Online Global WhatsMiner M30 Launch Event","introductionCn":"","introductionEn":"WhatsMiner will release the global M30 Launch Event online at 10:30pm on April 16th, 2020 (EDT or GMT-4:00)","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/%E6%9E%81%E8%87%B4%E5%8F%AF%E8%A7%81_1768461911852.jpg","channelId":1,"publishName":"WhatsMiner ","publishDate":"2020-04-07","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 14:57:50","updateTime":"2026-01-15 15:25:14"},{"id":232,"titleCn":"比特微-神马D1 Blake256算法服务器","titleEn":"MicroBT-WhatsMiner D1 for Blake256 Server","introductionCn":"","introductionEn":"This is the evaluation of Whatsminer D1 Blake256 server.","cover":"https://aws-microbt-com-bucket.s3.us-west-2.amazonaws.com/DI256_1768463066909.jpg","channelId":2,"publishName":"Alen ","publishDate":"2019-04-17","status":1,"isTop":0,"isRecommend":0,"isDeleted":0,"createTime":"2022-03-31 16:00:19","updateTime":"2026-01-15 15:44:29"}],"channel":{"id":2,"nameCn":"评测","nameEn":"Blog","sortNum":2,"status":1,"isDeleted":0,"createTime":"2025-04-29 17:33:52","updateTime":"2025-04-29 17:33:52"}},"timestamp":1794512166474,"requestTime":1794512166468,"executeTime":6}